Discussion Forum - Northstar Chevelle Club

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: Engine swap on '66 (or, out with the 283 and in with the 327)


Active Member

Status: Offline
Posts: 141
Date:
Engine swap on '66 (or, out with the 283 and in with the 327)
Permalink  
 


Last weekend I finally got around to starting a project that I have been working up to for some time - the engine and transmission swap in my 66 malibu ragtop "Loosie".  (she got that name because her brakes are loosie, her steering is loosie, doors are loosie, etc. etc.)   I managed to get the old smoke machine and three-speed out on Saturday, and a Craigslist ad made short work of the both of them.  I think the Saginaw was still in pretty decent shape, and I tried to be as clear about the condition of the engine as possible (it was drinking  a quart of cheap oil every hundred miles and still had the factory spark plugs.) Some guy from Iowa made off with the both of them for $125 plus some beer.  (By that I mean HE paid ME, which may come as a surprise)  Apparently they have lower standards down there?

Anyway, I started to put the engine/trans together and found out that I had ordered the wrong clutch assembly (online) for my flywheel.  Off to NAPA for a whole new setup, and $100+ later I am back in business.  I had also planned to do the power steering swap while the engine was out, so I pulled out the new steering box that I had also ordered online. You guessed it:  wrong.  Unfortunately, I ordered it last year in anticipation of this project, so I am stuck with the 99 Jeep Grand Cherokee power steering box that they shipped instead of the 96 that I ordered.  Nothing that Autozone and $134 can't remedy. 

You may already be calling me Johnny Wrongpart, but that isn't all:

The new radiator didn't fit - direct swap my ass.  I had to take the factory shroud off just to make enough room.  Now the factory hoses don't reach. 

The new proportioning valve sat very neatly right where the bellcrank goes for the clutch.  I fabbed up a small bracket to relocate it an inch forward, but it ain't pretty. 

The water pump bumped into the timing cover.  Double gaskets gave me a teeny clearance, but: haven't people been making aftermarket parts for these engines for sixty years now? You'd think that they would know where the ass was. 

The really cool, shiny power steering pump bracket assembly from Summit doesn't fit short water pumps.  This would be very useful information were it to be supplied to you BEFORE you order the item. 

The "direct replacement" battery cable was too short.  I think they must have been measuring in those little Chinese feet. 

Ugh. 

I haven't gotten it to the stage where I can fire the engine and see if I did everything right or if I have just built a boat anchor.  This is my first engine in 30+ years, and almost everything came from the internet - including the knowhow.  I built the engine and did a complete overhaul on the Muncie and the Hurst shifter, having never even seen one before.  Expect me to come to the next club event in reverse and on fire.  And without power steering. 

I may or may not have attached a photo for your amusement (The 11-year-old isn't here to walk me through it). If I did: that is the old distributor, now converted to a pre-oiler by grinding down the drive gear and busting off the advance bar.  The DeWalt is the best thing I can think of to power it, and I ran it for about 10 minutes this morning - until most of the pushrods were spitting oil.  The vintage Edelbrock valve covers are from Craigslist, ditto the intake. Notice the fat aluminum radiator: that thing could cool a P-51. It looks more like a toaster than an auto part. 

More to follow. Comments invited. 

John 

 

 

 



Attachments
__________________

John B. 1966 Malibu Ragtop  327, Tremec 6-speed, 4.11 10-bolt posi.  And ALWAYS a work in progress.



Active Member

Status: Offline
Posts: 141
Date:
Permalink  
 

The good news is that the photo appears above. The bad news is that some of you have desktop computers that are not easily rotated. Sorry.
The brake setup is 1967 booster and MC, with home-bent and flared lines down to the valve. I couldn't figure out how to get a perfect coil in the lines at the master cylinder, and finally resigned myself to rookie-looking bends. If anyone has a trick to share, I might take another shot.

John

__________________

John B. 1966 Malibu Ragtop  327, Tremec 6-speed, 4.11 10-bolt posi.  And ALWAYS a work in progress.



2K+ Club

Status: Offline
Posts: 2444
Date:
Permalink  
 

Looks great, sounds like your sprits are high and you still have a wonderful since of humor. Your post started my morning off with a good laugh and brought back many memories we all share of ill-fitting parts. When I did the Buick I sent back a lot of parts; Amazon makes it pretty easy.
When the fire is out, the car moves under its own power and your sitting at the first car show you will soon forget the one step forward two steps back and banging your head against the garage floor saga.
I’ve ground a fair amount of steel off water pumps to make them fit, might work for you also. I've used a baseball bat or piece of pipe to wrap lines around.
Very nice car buy the way


__________________

Kevin

Northwestern Ohio



President

Status: Offline
Posts: 7328
Date:
Permalink  
 

That's a drum brake master....are the front brakes still drum ?

I have the same style priming pump from the 70's. Works very well...cool

Different angle of the madness.



__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS/RS 350 M20



Active Member

Status: Offline
Posts: 141
Date:
Permalink  
 

I ordered a rear drum/front disc master from the friendly guys at NAPA, and that's what I got. I figured the '67 parts would be a good swap for hood clearance. The fronts are new discs, so I am counting on that being a disc master. Although, if I am going to keep the story going, it kind of has to be a drum/drum, doesn't it?

Thanks for fixing my photo.

John

__________________

John B. 1966 Malibu Ragtop  327, Tremec 6-speed, 4.11 10-bolt posi.  And ALWAYS a work in progress.



Secretary

Status: Offline
Posts: 2941
Date:
Permalink  
 

I believe I have a spare disc/drum master.

__________________

Bryan-NW 'burbs
1972 Malibu
Vaguely stock appearing, and the opposite of restored.
1999 std bore 5.7, Vortec heads, Holley Stealth Ram, GM cam
700R4, Viking coilovers, 12 bolt 4.10 posi, and a whole bunch more



3K+ Club

Status: Offline
Posts: 4731
Date:
Permalink  
 

Hang in there John, now it's all the nit picky/fabrication required/I did it myself stuff to get it going, which you will overcome!  If you hadn't pointed out the spiral bends on the master cylinder, I wouldn't have noticed at all.  I'm not a big '66/67 guy, so they would probably notice, but at some point a guy has to not worry about others and just get that puppy on the road and drive it!

Keep up the good work!  thumbsup



__________________

Stan S.-Twin Cities 'South Metro'

1972 Malibu Convertible 2nd time around 

2001 Mustang GT Convertible 

Forum influenced terms: 'Link Paste', 'Stanitized', & 'Revolving garage door...' 

 



President

Status: Offline
Posts: 7328
Date:
Permalink  
 

I have a correct 67' disc/drum master from Inline Tube. They also used the hold off valve as seen in the pics. This is with an 11" booster. I've since swapped in a correct 9" booster. I too had to move the distribution block to the top of the frame, right behind the z-bar for header clearance. I retained the original distribution block, that is why the hold off valve is needed. If you went to an aftermarket distribution block, you shouldn't need the hold off.

A drum master will hold too much residual pressure on the calipers and overheat the pads/discs.

 

 

 



__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS/RS 350 M20



Active Member

Status: Offline
Posts: 141
Date:
Permalink  
 

Nice looking car Mitch! I am looking at the photos, and I can't tell the difference between the master cylinders. I opted for a modern-style integrated proportioning valve, so there wasn't a need for the hold-off valve under the master - is that what you are noticing? Those "hand-bent" lines go right down to the front and the rear inlets on the PV. Like I say, when I ordered the master, I was told that it was a disc/drum master.

John

__________________

John B. 1966 Malibu Ragtop  327, Tremec 6-speed, 4.11 10-bolt posi.  And ALWAYS a work in progress.



President

Status: Offline
Posts: 7328
Date:
Permalink  
 

Yeah, you can't see the top directly but the front chamber for the discs is larger than the rear. I can't see that detail on yours either, so it may be the same. Hopefully, the residuals are correct in yours for the disc and drum applications.
Those "hand bent" coils are fine. Most people don't bother trying to reproduce the coil by hand at all....dunno



__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS/RS 350 M20



Active Member

Status: Offline
Posts: 141
Date:
Permalink  
 

So I went out to the garage and took a rubbing of the casting number (It's under the cylinder so I can't get to it to read it, but greazy hands on a piece of printer paper did the trick) : 5468115.  According to the web, this is a pretty standard casting that was used for a whole bunch of years for disc/drum cars, into the mid '70s.  I think the NAPA guys probably have a crossover guide that tells them that it will work in a '67 system, even though it is not 'correct' for the car.  As long as she stops on less than a dollar, I'll be happy.  

 

 

JOhn 



__________________

John B. 1966 Malibu Ragtop  327, Tremec 6-speed, 4.11 10-bolt posi.  And ALWAYS a work in progress.



1K+ Club

Status: Offline
Posts: 1724
Date:
Permalink  
 

I have seen the big/little reservoir not always be true for disc/drum setup. In fact the master on my camaro has the same size front and back and it works with my disc/drum setup with no problems. Big test will be the first test drive and how the pedal feels and how it stops.



__________________

Chris P
East Central, Mn

66 Chevelle 300 deluxe



Active Member

Status: Offline
Posts: 141
Date:
Permalink  
 

Thanks for all the help, guys. She is up and running, and I am ironing out some of the details. Right now, the rear brakes aren't doing anything. I replaced the shoes, adjusted, and bled, so I am kind of guessing at this point that the wheel cylinders were shot on the car. I noticed when I jacked the thing up and spun a wheel around that the opposite wheel doesn't move at all. I was expecting it to spin in the opposite direction (or maybe get lucky and have a posi ) - but I have no idea what it means if the other wheel does nothing. Does that mean that I just have a worn out diff?


John

__________________

John B. 1966 Malibu Ragtop  327, Tremec 6-speed, 4.11 10-bolt posi.  And ALWAYS a work in progress.



President

Status: Offline
Posts: 7328
Date:
Permalink  
 

Grajmahal wrote:

Thanks for all the help, guys. She is up and running, and I am ironing out some of the details. Right now, the rear brakes aren't doing anything. I replaced the shoes, adjusted, and bled, so I am kind of guessing at this point that the wheel cylinders were shot on the car. I noticed when I jacked the thing up and spun a wheel around that the opposite wheel doesn't move at all. I was expecting it to spin in the opposite direction (or maybe get lucky and have a posi ) - but I have no idea what it means if the other wheel does nothing. Does that mean that I just have a worn out diff?


John


 No, just means the spider gears were spinning and not turning the other axle gear.

If the rear wheel cylinders are seized, it could prevent the brakes from working. What happens that you don't think they are doing anything ?



__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS/RS 350 M20



Active Member

Status: Offline
Posts: 141
Date:
Permalink  
 

Well, I have had a lot of difficulty getting the rear brakes to bleed adequately after the front disc conversion. I installed a new line from the proportioning valve to the rubber line, and thought I had all of the air out of it. I bled the rears for what seemed like forever (I went through two volunteers on the pedal side if that is any indication) and finally was getting fluid consistently out of the bleeders and good feel at the pedal. However, with the back of the car jacked up, I could tell that the wheels still spin freely when the brake pedal is pressed. I figured that the cylinders must not be doing their job, so I ran out to O'Rielley tonight and got a new pair. Now it seems like no amount of bleeding will get even a little fluid out. I'd keep going, but it isn't even a sputter or a whoosh - just silence when I open the bleeder. I gave it about thirty tries on each side. Do I just need to keep bleeding these things for the rest of my life, or is there something else that needs doing that I am overlooking?

Thanks

John

__________________

John B. 1966 Malibu Ragtop  327, Tremec 6-speed, 4.11 10-bolt posi.  And ALWAYS a work in progress.



President

Status: Offline
Posts: 7328
Date:
Permalink  
 

Is the flex hose new too ??  If it is old, it can be swollen or cracked internally and block the flow.

I always leave the right rear bleeder open a couple turns and walk away for a while and let it bleed by gravity until it flows. Then do the left. Once I have fluid from both I go back to the right side and have a helper push the pedal down once while the bleeder is open, close the bleeder and do that a few times before going to the 3-4 pump method.



__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS/RS 350 M20



1K+ Club

Status: Offline
Posts: 1724
Date:
Permalink  
 

Sounds like the proportioning valve may have tripped itself and is not coming back. Hook a test light to B+ and touch the lead on the inside of the prop valve switch and see if the test light lights up. If it does the valve is tripped. You can unscrew the switch and use a screw driver to push the valve back to center in a worst case senerio and try to bleed it again.



__________________

Chris P
East Central, Mn

66 Chevelle 300 deluxe



President

Status: Offline
Posts: 7328
Date:
Permalink  
 

67ss wrote:

Sounds like the proportioning valve may have tripped itself and is not coming back. Hook a test light to B+ and touch the lead on the inside of the prop valve switch and see if the test light lights up. If it does the valve is tripped. You can unscrew the switch and use a screw driver to push the valve back to center in a worst case scenario and try to bleed it again.


 Doh, forgot about the prop valve. That is why I let a dry line gravity feed to avoid tripping the valve. I've been doing that so long I couldn't remember why I let them run first...cuckoo



__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS/RS 350 M20



Active Member

Status: Offline
Posts: 141
Date:
Permalink  
 

Thanks for the suggestions guys. And the winner is: Mitch, with the flex hose. I cracked the fitting at the rear end of the hard line, and plenty of fluid came out. I pulled the flex line and it was so obstructed that I couldn't even blow any air through it. I am amazed that something like this could fail such that a couple hundred PSI of fluid couldn't open it, but that was indeed the case. A new line in, a gravity bleed, and I am back in business. I wondered why the rear shoes and drums looked to be in such good condition; I suspect that they have never so much as touched since the last brake job. I now have new shoes and cylinders, so I should be set for a while.

Here's the creepy part: I have now learned that I drove from LA to Minneapolis, made numerous trips to the lake and all over town last fall and this summer, all on nothing but two front drum brakes. God must smile on the stupid.

I finally got the car out this evening for a trip around the block and down the freeway. Pedal feel is okay, though I suspect that a little more bleeding is in order. The power steering is fantastic - if you haven't done the Grand Cherokee swap, I recommend it. My disc kit lowered the car 2" and I installed a big front sway bar - neither of which seems to have had much effect on the car's handling. I go in tomorrow for an exhaust, so right now the open pipes make assessing anything else in the car almost impossible. The amazing part: an engine and transmission that a rookie put together in his garage over the winter actually function! I know you guys probably have that feeling all the time, but for me, it is still a little frightening and thrilling. The engine fires right up on the first click, the Muncie shifts like a dream, the car turns and stops better than when it was new - is it normal to be waiting for the catastrophe?

Thanks again for all the help.

John

__________________

John B. 1966 Malibu Ragtop  327, Tremec 6-speed, 4.11 10-bolt posi.  And ALWAYS a work in progress.



President

Status: Offline
Posts: 7328
Date:
Permalink  
 

Congrats on getting it sorted out...dancenana

Once those hoses collapse, the pressure only seems to plug it tighter and you're talking more like 3 THOUSAND pounds of fluid pressure.

You'll be waiting for the other shoe to drop for a while. It takes some time to get comfortable with a lot of changes at the same time.



__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS/RS 350 M20

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Chatbox
Please log in to join the chat!