Discussion Forum - Northstar Chevelle Club

Members Login
Username 
 
Password 
    Remember Me  
NCC Forum Home Page -> NCC - Projects and Updates -> Having trouble getting the new fuel line through the frame front spring pearch area, need help.
Post Info TOPIC: Having trouble getting the new fuel line through the frame front spring pearch area, need help.
jim larson


2K+ Club

Status: Offline
Posts: 2739
Date:
Having trouble getting the new fuel line through the frame front spring pearch area, need help.
Permalink  
 

I can only get in about 15" and then it hangs up.  Any suggestions on helping snake it though there?  There is a support for the Control Arm inside the frame and not sure if it is suppose to go above that or below that.



__________________

Jim L

Lake City
jim larson


2K+ Club

Status: Offline
Posts: 2739
Date:
Permalink  
 

Got it. A 20 minute job after spending 4 hrs trying multiple approaches.  If anyone decides to attemp this contact me.



-- Edited by jim larson on Thursday 25th of January 2018 06:59:36 AM

__________________

Jim L

Lake City
Lost in the 60s


President

Status: Offline
Posts: 7328
Date:
Permalink  
 

jim larson wrote:

Got it. A 20 minute job after spending 4 hrs trying multiple approaches.  If anyone deceids to attemp this contact me.

 Yep, there is a secret handshake maneuver involving rotating the tube to get it thru.....but you already know that now...tiphat



__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS/RS 350 M20
jim larson


2K+ Club

Status: Offline
Posts: 2739
Date:
Permalink  
 

Don't know about the secret handshake, wish I would have.  I actually took a 12/2 electric wire, about 5' and snaked it through from the front, stripped off the outside insulation, feed the ground and another wire i n side the fuel line, taped the other wire to the outside of the fuel line with electrical tape, making a nice smooth end, grease it up and gave it a pull.  came right through.



__________________

Jim L

Lake City
Lost in the 60s


President

Status: Offline
Posts: 7328
Date:
Permalink  
 

Yep, good move. I've used actual fuel hose and a small zip tie to do the same thing.
Pulling works so much better than pushing.

__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS/RS 350 M20
jim larson


2K+ Club

Status: Offline
Posts: 2739
Date:
Permalink  
 

Lost in the 60s wrote:

Yep, good move. I've used actual fuel hose and a small zip tie to do the same thing.
Pulling works so much better than pushing.

 I tried the fuel hose first and the end where I hooked up to the fuel line  kept hanging up. I used a clamp on the hose and fuel line, maybe I should have just taped it with electrical tape. Also the fuel line hose would flex too much.  Any info on the washer?



-- Edited by jim larson on Thursday 25th of January 2018 08:20:35 AM

__________________

Jim L

Lake City
jim larson


2K+ Club

Status: Offline
Posts: 2739
Date:
Permalink  
 

Just finished up on the fuel line install. Kind of a pain bending the line a little here and there to get it to sit just right so it fits into the clips on the frame.  Used wood blocks and wood pry bars.  beamup



__________________

Jim L

Lake City
Lost in the 60s


President

Status: Offline
Posts: 7328
Date:
Permalink  
 

I'll be back in the shop tomorrow and try to run it thru the blast cabinet to clean all the scale off for measuring.

__________________

Mitch D.   River Falls, WI

Lifetime member of the "Cars apart Club"

1966 Chevelle SS 396 M20

1970 Chevelle SS 396 M20

1967 Camaro SS/RS 350 M20
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
NCC Forum Home Page -> NCC - Projects and Updates -> Having trouble getting the new fuel line through the frame front spring pearch area, need help.
Chatbox
Please log in to join the chat!