Discussion Forum - Northstar Chevelle Club

Members Login
Username 
 
Password 
    Remember Me  
NCC Forum Home Page -> NCC - Classifieds -> (3) 12-bolts for sale
Post Info TOPIC: (3) 12-bolts for sale
Derek69SS


Founding Member

Status: Offline
Posts: 2801
Date:
(3) 12-bolts for sale
Permalink  
 

68 12-bolt 4.10 posi - just pulled it out of my car... Useable as-is, but the gears are noisy. I replaced the axle bearings and seals, and pinion seal when I put it in my car 3 years ago (around 15,000miles). Posi works good (1.84 60' times on 17" street tires!) Housing was in tough shape when I got it. Axle tubes are pitted a little bit. The lower brackets were all busted up from air-shocks, so I welded on good brackets that I cut off a 10-bolt. No brakes. SOLD

69 12-bolt bare housing w/caps... really nice housing coded for 3.73 posi (very desireable codes - can check dates if interested) $450

68-72 (I forget which) 12-bolt bare housing NO CAPS. SOLD



-- Edited by Derek69SS on Thursday 8th of July 2010 03:03:57 PM

__________________

Derek Kiefer - Mantorville, MN

69 Malibu Pro-Touring stroker LS1-383/T56 - 69 SS396-325/3spd project
69SSConv


Active Member

Status: Offline
Posts: 446
Date:
Permalink  
 

Derek,

I might be interested in the 69 bare housing with caps (coded for 3.73's)?  Is this a shell? , no axle's, gears, does it have backing plates?

Loren

__________________

Loren B. - Princeton, MN

1969 Chevelle SS Convertible, Bright Torch Red, 396, 200-4R, 12 bolt 3.73 Posi

1969 Chevrolet C20, Orange/White, 350, 4-spd, 4.11

1980 Camaro, RS, Impulse Blue, 350, 200-4R, 3.73 Posi

1967 Chevelle Malibu 2-DR Hardtop.  In process
Derek69SS


Founding Member

Status: Offline
Posts: 2801
Date:
Permalink  
 

I do have axles, but When I put the 68 housing in my car a few years ago, I used the best 2 axles from the 2 housings... so the axles that come with it do show quite a bit of wear at the axle bearings. I think the backing plates are on it, but I'd have to look again... 10-bolts used the same brakes, so they're easy enough to find.

The original gears and carrier were pulled many years ago, and put into a '67 chevelle stock-car.

__________________

Derek Kiefer - Mantorville, MN

69 Malibu Pro-Touring stroker LS1-383/T56 - 69 SS396-325/3spd project
Chris R


2K+ Club

Status: Offline
Posts: 2766
Date:
Permalink  
 

If the rear end needs axles. Club member Charlie Mueller whom set us up with a very nice discount at Catco can get them.  

__________________

Chris - Ramsey, MN.

Dear Optimist, Pessimist, and Realist.

While you guys were busy arguing about the glass of water. I drank it!

Sincerly,

The opportunist.
Derek69SS


Founding Member

Status: Offline
Posts: 2801
Date:
Permalink  
 

The backing plates are on it, but they're a little bent up from being slid around on the shop floor. Casting date is B 4 9 (Feb 4th 1969)

__________________

Derek Kiefer - Mantorville, MN

69 Malibu Pro-Touring stroker LS1-383/T56 - 69 SS396-325/3spd project
69SSConv


Active Member

Status: Offline
Posts: 446
Date:
Permalink  
 

Derek,

I am interested, just in a major push to get the car on the road right now.  It's in the shop getting painted as I write this, and as soon as it comes out I will be focused on: fixing transmission leak, exhaust leak and install "H"pipe, installing glass, finishing trim, getting new top installed..... .  It would probably be May before I could pick it up?  If you have another serious buyer, go ahead, otherwise in May I could take it off your hands.

__________________

Loren B. - Princeton, MN

1969 Chevelle SS Convertible, Bright Torch Red, 396, 200-4R, 12 bolt 3.73 Posi

1969 Chevrolet C20, Orange/White, 350, 4-spd, 4.11

1980 Camaro, RS, Impulse Blue, 350, 200-4R, 3.73 Posi

1967 Chevelle Malibu 2-DR Hardtop.  In process
Derek69SS


Founding Member

Status: Offline
Posts: 2801
Date:
Permalink  
 

No problem... I'm not really in a hurry either. :)

__________________

Derek Kiefer - Mantorville, MN

69 Malibu Pro-Touring stroker LS1-383/T56 - 69 SS396-325/3spd project
Derek69SS


Founding Member

Status: Offline
Posts: 2801
Date:
Permalink  
 

TTT, still have all of them... will be posting to Craigslist soon.

Loren, you still interested in the '69 housing?

__________________

Derek Kiefer - Mantorville, MN

69 Malibu Pro-Touring stroker LS1-383/T56 - 69 SS396-325/3spd project
69SSConv


Active Member

Status: Offline
Posts: 446
Date:
Permalink  
 

Derek,

Sorry I didn't see this before now.  I did find a 12 bolt from a friend of mine and have started to rebuild that.  What I am trying to decide now if I should go with 3.55 gears or 3.73 gears, keeping in mind that I plan to put in a 200R4 at the same time that I swap the rear end?

Sorry to keep you hanging, I should have let you know sooner.

Just been frustrated with how long it is taking to get the car painted and my summer is slipping away.

Loren

__________________

Loren B. - Princeton, MN

1969 Chevelle SS Convertible, Bright Torch Red, 396, 200-4R, 12 bolt 3.73 Posi

1969 Chevrolet C20, Orange/White, 350, 4-spd, 4.11

1980 Camaro, RS, Impulse Blue, 350, 200-4R, 3.73 Posi

1967 Chevelle Malibu 2-DR Hardtop.  In process
Derek69SS


Founding Member

Status: Offline
Posts: 2801
Date:
Permalink  
 

No problem Loren, I have since sold the other 2 (at Back-to-the-50s swap) and decided to keep the '69 housing for now... might still let it go if someone comes along and offers enough, but not actively trying to sell it anymore.


-- Edited by Derek69SS on Thursday 8th of July 2010 03:04:51 PM

__________________

Derek Kiefer - Mantorville, MN

69 Malibu Pro-Touring stroker LS1-383/T56 - 69 SS396-325/3spd project
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
NCC Forum Home Page -> NCC - Classifieds -> (3) 12-bolts for sale
Chatbox
Please log in to join the chat!